Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 313

background image

Blade server controls and LEDs

Use this information for details about the controls and LEDs on the blade server and IBM MAX5 expansion
blade.

The following illustration identifies the buttons and LEDs on the blade server control panel.

MT

Power button / LED

KVM select
button / LED

Media tray select
button / LED

Activity LED

Location LED

Information LED

Fault LED

NMI button

NMI button (recessed)

The nonmaskable interrupt (NMI) dumps the partition. Use this recessed button only as directed by IBM
Support.

Note:

You can also send an NMI event to the selected blade server remotely using the AMM. Refer to

the

BladeCenter Advanced Management Module User's Guide

for information pertaining to the proper

installation and configuration of Java, operating systems, and browsers that are supported for remote
access.

Power button/LED

When the blade server has power, press this button to turn on or turn off the blade server.

Note:

The power button works only if local power control is enabled for the blade server. Local power

control is enabled and disabled through the advanced management module web interface.

After the blade server is removed from the chassis, press this button to activate the system board LEDs
(light path diagnostics). See “System-board LEDs - BladeCenter HX5” on page 15 for more information.

This button is also the power LED. This green LED indicates the power status of the blade server:

•

Flashing rapidly

: The LED flashes rapidly for one of the following reasons:

– The blade server has been installed in a chassis. When you install the blade server, the LED flashes

rapidly for up to 90 seconds while the integrated management module (IMM) on the blade server is
initializing and synchronizing with the advanced management module.

– The blade server does not have power permissions assigned to it through the advanced

management module.

– The BladeCenter chassis does not have enough power to turn on the blade server.

– The IMM on the blade server is not communicating with the advanced management module.

•

Flashing slowly

: The blade server has power and is ready to be turned on.

7

«
...
21
22
23
24
25
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

Power AC922 8335-GTW

Бренд: IBM Страницы: 70

DIGITAL Server 9100 Series

Бренд: Digital Equipment Страницы: 68

WECS II 2048/DMX/02

Бренд: Oase Страницы: 67

Бренд: ACE COMPUTERS Страницы: 32

Бренд: QNAP Страницы: 39

PRIMERGY econel 20

Бренд: Fujitsu Siemens Computers Страницы: 62

SPARC Enterprise M4000

Бренд: Fujitsu Siemens Computers Страницы: 162

ReadiManagerSE200

Бренд: Polycom Страницы: 4

Бренд: Planet Страницы: 72

Бренд: Gigabyte Страницы: 108

NETWORK SATELLITE 5.0.0 -

Бренд: Red Hat Страницы: 84

VANTAGE RADIUS 50

Бренд: ZyXEL Communications Страницы: 1

Бренд: ZyXEL Communications Страницы: 4

DIRECTORY SERVER 7.1

Бренд: Red Hat Страницы: 652

Бренд: ATEN Страницы: 111

Бренд: GIGA-BYTE TECHNOLOGY Страницы: 141

Бренд: Intel Страницы: 117

Бренд: GIGA-BYTE TECHNOLOGY Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды