Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 140

Страница: 140 / 313

Step 2. If the blade server or scalable blade complex is installed in a BladeCenter chassis, remove it. See

“Removing the blade server from the BladeCenter chassis” on page 66 for instructions.

Step 3. Carefully lay the blade server on a flat, static-protective surface.

Step 4. If you are installing the CIOv card in a blade server that is the bottom blade server in a scalable

blade complex, disassemble the blade complex (see “Disassembling a scalable blade complex” on
page 68 for instructions).

Step 5. If an optional expansion unit is installed, remove the expansion unit (see “Removing an expansion

unit” on page 96 for instructions).

Note:

Optional expansion units are not supported when a IBM MAX5 expansion blade is installed.

Step 6. If an IBM MAX5 expansion blade is installed, remove it (see “Removing an IBM MAX5 expansion

blade” on page 87 for instructions).

Step 7. Open the blade server cover (see “Removing the blade server cover” on page 71 for instructions).

Step 8. If a CFFh expansion card is installed, remove it (see “Removing a CFFh expansion card” on page

119 for instructions).

Step 9. Locate the CIOv expansion connector (see “Blade server connectors - BladeCenter HX5” on page

12).

Step 10. Touch the static-protective package that contains the expansion card to any

unpainted

metal

surface on the BladeCenter unit or any

unpainted

metal surface on any other grounded rack

component; then, remove the expansion card from the package.

Step 11. Orient the connector on the expansion card with the CIOv expansion connector on the system

board; then, press the card into the CIOv expansion connector.

Step 12. Firmly press on the indicated locations to seat the expansion card.

Note:

For device-driver and configuration information to complete the installation of the expansion

card, see the documentation that comes with the expansion card.

Step 13. Install the CFFh expansion card, if you removed one from the blade server (see “Installing a CFFh

expansion card” on page 122 for instructions).

Step 14. If the blade server is part of a scalable blade complex, assemble the scalable blade complex (see

“Assembling a scalable blade complex” on page 70 for instructions).

Step 15. Install the IBM MAX5 expansion blade if you removed one (see “Installing an IBM MAX5 expansion

blade” on page 88 for instructions).

Step 16. Install the optional expansion unit, if you removed one from the blade server (see “Installing an

expansion unit” on page 97 for instructions).

Step 17. Install the cover onto the blade server (see “Installing the blade server cover” on page 73 for

instructions).

Step 18. Install the blade server or scalable blade complex into the BladeCenter chassis (see “Installing a

blade server in a BladeCenter chassis” on page 67 for instructions).

Removing the control panel

Use this information to remove the control panel from the blade server.

To remove the control panel, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. If the blade server or scalable blade complex is installed in a BladeCenter chassis, remove it. See

“Removing the blade server from the BladeCenter chassis” on page 66 for instructions.

Step 3. Carefully lay the blade server on a flat, static-protective surface.

124

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды