Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 281 | Manualshive

Страница: 281 / 313

background image

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are CRUs and which

components are FRUs.

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

trained service technician.

Message

Action

System under recommended voltage for
+3.3 V.

Informational only.

Note:

If the problem remains, complete the following steps:

1. Reseat the blade server. See “Removing the blade server from the

BladeCenter chassis” on page 66 and “Installing a blade server in
a BladeCenter chassis” on page 67.

2. Check the function of the shared BladeCenter chassis resources.

See “Solving shared BladeCenter resource problems” on page
269.

3. (Trained service technician only) Replace the system-board

assembly. See “Removing the system-board assembly -
BladeCenter HX5” on page 140 and “Installing the system-board
assembly - BladeCenter HX5” on page 142.

System under recom5 V fault.

Informational only.

Note:

If the problem remains, complete the following steps:

1. Reseat the blade server. See “Removing the blade server from the

BladeCenter chassis” on page 66 and “Installing a blade server in
a BladeCenter chassis” on page 67.

2. Check the function of the shared BladeCenter chassis resources.

See “Solving shared BladeCenter resource problems” on page
269.

3. (Trained service technician only) Replace the system-board

assembly. See “Removing the system-board assembly -
BladeCenter HX5” on page 140 and “Installing the system-board
assembly - BladeCenter HX5” on page 142.

Power problems

Use this information to diagnose and resolve power problems for the blade server.

IBM continually updates the support website with tips and techniques that you can use to resolve any
problems that you might be having with the BladeCenter HX5 blade server. Go to the BladeCenter support
search website at http://www.ibm.com to see if any service bulletins have been generated. In the Search
field, enter the following terms: 7872, retain tip, and power.

Follow the suggested actions in the order in which they are listed in the Action column until the problem is
solved.

265

«
...
279
280
281
282
283
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

eserver xSeries 306

Бренд: IBM Страницы: 46

SuperServer 6041G

Бренд: Supero Страницы: 114

NPort IA5250I/5250I-T Series

Бренд: Moxa Technologies Страницы: 2

Бренд: Yawarra Страницы: 4

AcquiLite A7810-0

Бренд: Obvius, LLC Страницы: 29

ApplianceStor 90

Бренд: Rasilient Страницы: 42

Бренд: Alfresco Страницы: 49

Бренд: ClearCube Страницы: 15

Бренд: Coolmax Страницы: 31

Xtreme PC LXN2321

Бренд: Chip PC Страницы: 4

Бренд: Gigabyte Страницы: 108

NETWORK SATELLITE 5.0.0 -

Бренд: Red Hat Страницы: 84

Бренд: innuos Страницы: 11

Бренд: Nexcom Страницы: 87

Бренд: Elastix Страницы: 5

SecureBox SDS2100

Бренд: Lantronix Страницы: 70

STRATOS S210 Series S210-X22RQ

Бренд: QUANTA Страницы: 252

Бренд: DBM Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды