Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 112

Страница: 112 / 313

Step 13. Alternately tighten the screws on the 1-node scalability card by hand to ensure that the screw

threads start properly.

Important:

Always hand tighten each screw before you use the 3/16" hex driver.

Step 14. Install the blade server cover (see “Installing the blade server cover” on page 73 for instructions).

Step 15. Install the blade server into the chassis (see “Installing a blade server in a BladeCenter chassis” on

page 67 for instructions).

Removing an expansion unit

Use these instructions to remove an expansion unit from a blade server or from the topmost blade server in a
scalable blade complex.

Blade server
cover release

Cover
Pins

To open and remove an expansion unit, complete the following steps.

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. If the blade server or scalable blade complex is installed in a BladeCenter chassis, remove it. See

“Removing the blade server from the BladeCenter chassis” on page 66 for instructions.

Step 3. Carefully lay the blade server on a flat, static-protective surface, orienting the blade server with the

bezel pointing toward you.

Step 4. Open the blade server cover (see “Removing the blade server cover” on page 71 for instructions).

Step 5. Press the blade server cover release on each side of the blade server and lift the expansion unit

from the blade server.

Step 6. Rotate the expansion blade open; then, lift the expansion blade from the blade server.

Step 7. If additional expansion units need to be removed, repeat steps Step 5 on page 96 and Step 6 on

page 96.

Step 8. If you are instructed to return the expansion unit, follow all packaging instructions, and use any

packaging materials for shipping that are supplied to you.

Important:

Do not return the blade cover. You will need to install the blade cover from the

BladeCenter HX5 on to the new expansion unit. The BladeCenter HX5 blade cover contains the
system-service label on the bottom of the cover.

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды