Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 286 | Manualshive

Страница: 286 / 313

background image

Keyboard or mouse problems

Use this information to diagnose and resolve keyboard and mouse issues.

To check for keyboard or mouse problems, complete the following steps until the problem is solved:

Step 1. Make sure that:

• Both the blade server and the monitor are turned on.
• The keyboard/video/mouse select button LED on the front of the blade server is lit, indicating

that the blade server is connected to the shared keyboard and mouse.

• The keyboard or mouse cable is securely connected to the active BladeCenter advanced

management module.

• The keyboard or mouse works with another blade server.

Step 2. Check for correct advanced management module operation (see the documentation for your

BladeCenter chassis).

Note:

Some BladeCenter chassis types have several management-module components that might

have to be tested or replaced (see the

Installation Guide

for your advanced management module

for more information).

Step 3. Replace the keyboard or mouse.

Step 4. Replace the advanced management module (see the documentation for your BladeCenter chassis).

If these steps do not solve the problem, it is likely a problem with the blade server. See “Keyboard or mouse
problems” on page 256.

Media tray problems

Use this information to diagnose and resolve media tray issues for the blade server.

To check for problems with the media tray (removable media drives and USB ports), complete the following
steps until the problem is solved:

Step 1. Make sure that:

• The media-tray select button LED on the front of the blade server is lit, indicating that the blade

server is connected to the shared media tray.

• The media tray devices work with another blade server.

Step 2. Determine whether the problem affects more than one media tray component:

• USB ports
• CD or DVD drive

Step 3. For problems that affect only a USB port:

a. Make sure that the USB device is operational. If you are using a USB hub, make sure that the

hub is operating correctly and that any software that the hub requires is installed. Connect the
USB device directly to the USB port, bypassing the hub, to check its operation.

b. Reseat the following components:

1. USB device cable

2. Media tray cable (if applicable)

3. Media tray

c. Replace the following components one at a time, in the order shown, restarting the blade

server each time:

1. USB cable (if applicable)

2. Media tray cable (if applicable)

270

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

«
...
284
285
286
287
288
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

Бренд: Watchguard Страницы: 32

RS/6000 44P Series 270

Бренд: IBM Страницы: 346

BACnet/IP Server-SUNWAYS

Бренд: IntesisBox Страницы: 5

Бренд: Avaya Страницы: 84

BullSequana Edge nano

Бренд: Atos Страницы: 29

PRIMERGY RX300 S6

Бренд: Fujitsu Страницы: 132

PRIMERGY RX300 S5

Бренд: Fujitsu Страницы: 112

PRIMERGY RX2540 M4

Бренд: Fujitsu Страницы: 86

PRIMERGY RX2540 M6

Бренд: Fujitsu Страницы: 121

PRIMERGY RX4770 M6

Бренд: Fujitsu Страницы: 468

PRIMERGY RX2540 M1

Бренд: Fujitsu Страницы: 92

PRIMERGY RX2540 M5

Бренд: Fujitsu Страницы: 112

PRIMERGY RX2540 M4

Бренд: Fujitsu Страницы: 639

PRIMERGY RX2540 M2

Бренд: Fujitsu Страницы: 602

PRIMERGY RX2530 M5

Бренд: Fujitsu Страницы: 486

PRIMERGY RX2540 M1

Бренд: Fujitsu Страницы: 438

PRIMERGY RX300 S5

Бренд: Fujitsu Страницы: 66

SUPERSERVER 7045W-NTR+

Бренд: Supero Страницы: 146

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды