Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 133

Страница: 133 / 313

1. Using a screwdriver, remove each of the screws on the right access panel.

2. Lift the access panel away from the blade server.

Step 9. Remove the hypervisor interposer:

a. Locate the hypervisor interposer on the system board (see “Parts listing - BladeCenter HX5”

on page 57).

b. Press down on the front edge of the hypervisor interposer to disengage the hypervisor

interposer from the hypervisor interposer card guide.

c. Carefully lift the hypervisor interposer up from the system board.

d. Pull the hypervisor key away from the hypervisor interposer, if one is installed.

Step 10. Touch the static-protective package that contains the hypervisor key to any

unpainted

metal

surface on the BladeCenter unit or any

unpainted

metal surface on any other grounded rack

component in the rack in which you are installing the hypervisor key for at least 2 seconds; then,
remove the USB module from its package.

Step 11. Install the hypervisor key into the hypervisor adapter:

a. Orient the connector on the hypervisor key with the connector on the hypervisor adapter.

b. Use your fingers to push the hypervisor key into the hypervisor adapter.

Step 12. Install the hypervisor adapter:

a. Orient the connector on the hypervisor interposer with the interposer connector on the system

board, aligning the pins on the side of the hypervisor interposer with the pinholes on the
interposer connector (see “Blade server connectors - BladeCenter HX5” on page 12).

b. Use your fingers to push the adapter into the connector on the blade server.

Attention:

Be careful not to damage the pins on the hypervisor interposer.

Step 13. Install the access panel:

There are two types of access panels available for the BladeCenter HX5 blade server, depending
on whether tall heat sinks are installed.

• Complete the following steps to install the access panel on a BladeCenter HX5 blade server that

does not have tall heat sinks:

Chapter 4

Removing and replacing blade server components

117

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды