Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 282

Страница: 282 / 313

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are CRUs and which

components are FRUs.

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

trained service technician.

Symptom

Action

The power button does not
work.

1. Reseat the control-panel connector. See “Blade server controls and LEDs” on

page 7.

2. (Trained service technician only) Replace the system-board assembly. See

“Removing the system-board assembly - BladeCenter HX5” on page 140 and
“Installing the system-board assembly - BladeCenter HX5” on page 142.

The blade server does not turn
on.

1. Check the function of the shared BladeCenter chassis resources. See “Solving

shared BladeCenter resource problems” on page 269.

2. Make sure that the power-on LED on the blade server control panel is flashing

slowly. See “Blade server controls and LEDs” on page 7.
• If the power LED is flashing rapidly and continues to do so, the blade server

is not communicating with the advanced management module; reseat the
blade server. See “Removing the blade server from the BladeCenter chassis”
on page 66 and “Installing a blade server in a BladeCenter chassis” on page
67.

• If the power LED is off, the blade server bay is not receiving power, the blade

server is defective, or the operator control panel is loose or defective. See
“Removing the blade server from the BladeCenter chassis” on page 66 and
“Installing a blade server in a BladeCenter chassis” on page 67. In addition,
see “Removing the control panel” on page 124 and “Installing the control
panel” on page 126.

3. Check the power-management policies in the operating system for the blade

server. See the

Advanced Management Module User's Guide

for more

information.

4. Check the advanced management module event log of the corresponding blade

server for an error that is preventing the blade server from turning on. See
“Event logs” on page 147.

5. Reseat the blade server. See “Removing the blade server from the BladeCenter

chassis” on page 66 and “Installing a blade server in a BladeCenter chassis” on
page 67.

6. If you just installed a device in the blade server, remove it and restart the blade

server. If the blade server now starts, you might have installed more devices
than the power to that blade server bay supports.

7. (Trained service technician only) If you tried another blade server in the blade

server bay when you check the function of the shared BladeCenter chassis
resources and the other blade server worked, replace the system-board
assembly. See “Removing the system-board assembly - BladeCenter HX5” on
page 140 and “Installing the system-board assembly - BladeCenter HX5” on
page 142.

8. See “Solving undetermined problems” on page 274.

266

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды