Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 313

background image

Removing a solid state drive

Use this information to remove a solid state drive.

The blade server has a solid state drive expansion card for installing or removing solid state drives. To
remove a solid state drive, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. If the blade server or scalable blade complex is installed in a BladeCenter chassis, remove it. See

“Removing the blade server from the BladeCenter chassis” on page 66 for instructions.

Step 3. Carefully lay the blade server on a flat, static-protective surface.

Step 4. Open the blade server cover (see “Removing the blade server cover” on page 71 for instructions).

Step 5. If an optional expansion unit is installed, remove the expansion unit (see “Removing an expansion

unit” on page 96 for instructions).

Note:

Optional expansion units are not supported when a IBM MAX5 expansion blade is installed.

Step 6. If you are removing the SSD expansion card from a blade server that is the bottom blade server in a

scalable blade complex, disassemble the blade complex (see “Disassembling a scalable blade
complex” on page 68 for instructions).

Step 7. If an IBM MAX5 expansion blade is installed, remove it (see “Removing an IBM MAX5 expansion

blade” on page 87 for instructions).

Step 8. If a CFFh expansion card is installed, remove it (see “Removing a CFFh expansion card” on page

119 for instructions).

Step 9. Remove the SSD expansion card (see “Removing an SSD expansion card” on page 98 for

instructions).

Step 10. Turn over the SSD expansion card.

Step 11. Press down on the blue tab. The retention lever automatically opens so that the solid state drive or

drives are accessible.

Step 12. Slide the solid state drive out of the slot.

Note:

When you remove a drive from the SSD expansion card, consider labeling the drive to

indicate the slot from which the drive was removed so that you can install the drive back in to the
same slot.

Step 13. Close the retention lever and secure it with the blue tab.

Note:

You might have to press the blue tab before you close the retention lever.

Step 14. If you are instructed to return the solid state drive, follow all packaging instructions, and use any

packaging materials for shipping that are supplied to you.

Removing and replacing blade server components

101

«
...
115
116
117
118
119
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

SuperServer 5039MD18-H8TNR

Бренд: Supermicro Страницы: 134

NPort W2150Plus Series

Бренд: Moxa Technologies Страницы: 167

Rackmount 5000 Series

Бренд: Johnson Controls Страницы: 42

MES3-255C-DM-EN

Бренд: Mitsubishi Electric Страницы: 48

apricot FTs 486

Бренд: Mitsubishi Electric Страницы: 17

Бренд: Mitsubishi Electric Страницы: 32

Бренд: Mitsubishi Electric Страницы: 117

Бренд: TYAN Страницы: 80

B8236G70W8HR-HE

Бренд: TYAN Страницы: 84

Бренд: TYAN Страницы: 82

Бренд: Polycom Страницы: 11

Бренд: Viavi Страницы: 7

Бренд: Datum Страницы: 54

IntraPort Enterprise-2

Бренд: Compatible Systems Страницы: 43

Бренд: Lantronix Страницы: 92

Sun Server X4-4

Бренд: Oracle Страницы: 148

UniServer R4900 G6 Ultra

Бренд: H3C Страницы: 74

Бренд: Assmann Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды