Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 210

Страница: 210 / 313

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is

solved.

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are CRUs and which

components are FRUs.

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

trained service technician.

Type

Error Message

Action

Error

Group 4, processor (One of CPUs)
configuration error

1. (Trained service personnel only) Remove the blade server

and reseat the processors (see “Removing a
microprocessor and heat sink” on page 130 and “Installing
a microprocessor and heat sink” on page 134).

2. Verify that the system is running the latest UEFI firmware

(see “Updating firmware and device drivers” on page 30).

3. Run the Setup utility (see “Using the Setup utility” on page

20).

a. Make sure that both processors are displayed by the

system.

b. Load the default settings.

c. Go to the

System Settings

menu and make sure the

processor is enabled.

Error

Group 4, processor (4S CPU)
configuration error

1. (Trained service personnel only) Remove the blade server

and reseat the processors (see “Removing a
microprocessor and heat sink” on page 130 and “Installing
a microprocessor and heat sink” on page 134).

2. Verify that the system is running the latest UEFI firmware

(see “Updating firmware and device drivers” on page 30).

3. Run the Setup utility (see “Using the Setup utility” on page

20).

a. Make sure that both processors are displayed by the

system.

b. Load the default settings.

c. Go to the

System Settings

menu and make sure the

processor is enabled.

Error

Group 4, processor (2S CPU)
configuration error

1. (Trained service personnel only) Remove the blade server

and reseat the processors (see “Removing a
microprocessor and heat sink” on page 130 and “Installing
a microprocessor and heat sink” on page 134).

2. Verify that the system is running the latest UEFI firmware

(see “Updating firmware and device drivers” on page 30).

3. Run the Setup utility (see “Using the Setup utility” on page

20).

a. Make sure that both processors are displayed by the

system.

b. Load the default settings.

c. Go to the

System Settings

menu and make sure the

processor is enabled.

194

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды