Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 313

background image

Note:

Before installing an IBM MAX5 expansion blade option, make sure that you have updated the firmware

on the BladeCenter HX5 blade server to the latest level. If you attach and try to use the IBM MAX5 expansion
blade without updating the server firmware, you might get unexpected system behavior or the server might
not power on. For information about updating the firmware on the BladeCenter HX5 blade server, see
“Updating firmware and device drivers” on page 30.

There are two versions of the IBM MAX5 expansion blade, referred to as the IBM MAX5 version 1 and IBM
MAX5 version 2 in this document. IBM MAX5 version 2 has a "MAX5" identifying label on the bottom of the
front bezel. The functionality of the two IBM MAX5 expansion blades are equivalent except for the type of
DIMMs supported. The type of DIMMs supported will differ, depending on the version of IBM MAX5
expansion blade installed. For the list of DIMMs available for your IBM MAX5 expansion blade, see “Parts
listing - IBM MAX5” on page 62 or go to http://www.ibm.com/supportportal/ for an updated parts listing.

To install an IBM MAX5, complete the following steps.

IBM MAX5

Power
jumper

Blade server
cover release

Blade server
cover release

Upper
ridge

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. If the blade server is installed in a BladeCenter chassis, remove it (see “Removing the blade server

from the BladeCenter chassis” on page 66 for instructions).

Step 3. Carefully lay the blade server on a flat, static-protective surface.

Step 4. Open the blade server cover (see “Removing the blade server cover” on page 71 for instructions).

Step 5. If an optional expansion unit is installed, remove the expansion unit (see “Removing an expansion

unit” on page 96 for instructions).

Note:

Optional expansion units are not supported when a IBM MAX5 expansion blade is installed.

.

Removing and replacing blade server components

89

«
...
103
104
105
106
107
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

QS21 - BladeCenter - 0792

Бренд: IBM Страницы: 110

Link Manager 4010-43

Бренд: Point Six Страницы: 131

Бренд: TYAN Страницы: 77

Crestron 908012

Бренд: SIERRA VIDEO SYSTEMS Страницы: 32

SUPERSERVER 5015M-MF

Бренд: Supero Страницы: 120

SuperServer 2028R-C1R(T)4+

Бренд: Supermicro Страницы: 1

ProLiant DL100 G2 DPSS

Бренд: HP Страницы: 155

NetStorage 6000

Бренд: HP Страницы: 192

ProLiant DL100 G2 DPSS

Бренд: HP Страницы: 44

Бренд: EDSLab Страницы: 24

TourMaster MLA2504

Бренд: Coachsound Страницы: 22

Бренд: Kramer Страницы: 28

VISION2 V2-MASTER-0300

Бренд: AMX Страницы: 2

MINISTATION MFA500

Бренд: Plustek Страницы: 92

SafeNet ProtectServer Network HSM 5.9

Бренд: Thales Страницы: 37

Exadata Storage Server X7-2 EF

Бренд: Oracle Страницы: 90

DiskStation DS114

Бренд: Synology Страницы: 16

Бренд: Oracle Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды