Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 313

background image

Parts listing - IBM MAX5

The following replaceable components are available for the IBMIBM MAX5 expansion blade. There are two
versions of the IBM MAX5 expansion blade, referred to as the IBM MAX5 version 1 and IBM MAX5 version 2
in this document. IBM MAX5 version 2 has a "MAX5" identifying label on the bottom of the front bezel. The
functionality of the two IBM MAX5 expansion blades are equivalent except for the type of DIMMs supported.
The type of DIMMs supported will differ, depending on the version of IBM MAX5 expansion blade installed.

For an updated parts listing on the web, complete the following steps.

Note:

Changes are made periodically to the IBM website. The actual procedure might vary slightly from what

is described in this document.

1. Go to http://www.ibm.com/supportportal/.

2. Under

Product support

, click

BladeCenter

.

3. Under

Popular links

, click

Part documents lookup

.

4. From the

Product Family

menu, select

BladeCenter HX5

and click

Go

.

Note:

The illustrations in this document might differ slightly from your hardware.

Replaceable components are of four types:

•

Tier 1 customer replaceable unit (CRU):

Replacement of Tier 1 CRUs is your responsibility. If IBM

installs a Tier 1 CRU at your request, you will be charged for the installation.

•

Tier 2 customer replaceable unit:

You may install a Tier 2 CRU yourself or request IBM to install it, at no

additional charge, under the type of warranty service that is designated for your server.

•

Field replaceable unit (FRU):

FRUs must be installed only by trained service technicians.

62

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

«
...
76
77
78
79
80
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

Бренд: Basalte Страницы: 2

Бренд: SMART-AVI Страницы: 43

SafeNet ProtectServer PCIe HSM

Бренд: Gemalto Страницы: 17

Бренд: Silicon Graphics Страницы: 72

Бренд: Check Point Страницы: 53

Бренд: CTC Union Страницы: 53

T4MFCS Scaleout

Бренд: VVDN Страницы: 37

Бренд: Xiva Страницы: 41

Бренд: Gateway Страницы: 14

hospitality 9700

Бренд: Oracle Страницы: 11

PowerEdge R740xd2

Бренд: Dell EMC Страницы: 197

Бренд: Xblue Networks Страницы: 17

Бренд: Gigabyte Страницы: 56

Бренд: Gigabyte Страницы: 81

Бренд: Gigabyte Страницы: 84

FusionServer 2488H V6

Бренд: xFusion Digital Technologies Страницы: 116

ActiveScale X100

Бренд: Quantum Страницы: 265

Бренд: Lanner Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды