Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 124 | Manualshive

Страница: 124 / 313

background image

To remove a DIMM, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. Carefully lay the expansion blade on a flat, static-protective surface.

Step 3. Open the expansion blade cover (see “Removing the blade server cover” on page 71 for

instructions).

Step 4. If the IBM MAX5 expansion blade is installed on an BladeCenter HX5 blade server that is installed in

a BladeCenter chassis:

a. Remove the blade server from the chassis (see “Removing the blade server from the

BladeCenter chassis” on page 66 for instructions).

b. Remove the IBM MAX5 expansion blade (see “Removing an IBM MAX5 expansion blade” on

page 87 for instructions).

Step 5. Locate the DIMM connectors (see “Blade server connectors - IBM MAX5” on page 14). Determine

which DIMM you want to remove from the expansion blade.

Attention:

To avoid breaking the retaining clips or damaging the DIMM connectors, handle the

clips gently.

Step 6. Make sure that both retaining clips on DIMM connector from which you will be removing the DIMM

are in the open position.

Step 7. Using your fingers, pull the DIMM out of the connector.

Step 8. If you are instructed to return the DIMM, follow all packaging instructions, and use any packaging

materials for shipping that are supplied to you.

Installing a DIMM - IBM MAX5

The expansion blade has a total of 24 dual inline memory module (DIMM) connectors. The expansion blade
supports 2 GB (Type 7873 models), 4 GB, 8 GB, 16 GB (Type 7873 models), and 32 GB (Type 7873 models)
memory DIMMs. Typically, you will install all memory supported by the BladeCenter HX5 blade server before
installing memory in the IBM MAX5 expansion blade.

There are two versions of the IBM MAX5 expansion blade, referred to as the IBM MAX5 version 1 and IBM
MAX5 version 2 in this document. IBM MAX5 version 2 has a "MAX5" identifying label on the bottom of the
front bezel. The functionality of the two IBM MAX5 expansion blades are equivalent except the type of
DIMMs supported. The type of DIMMs supported will differ, depending on the version of IBM MAX5
expansion blade installed.

108

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

«
...
122
123
124
125
126
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

Altos R700 Series

Бренд: Acer Страницы: 80

Altos G700 series

Бренд: Acer Страницы: 14

Бренд: Acer Страницы: 103

Altos R720 Series

Бренд: Acer Страницы: 104

RS/6000 7043 43P Series

Бренд: IBM Страницы: 322

System x3400 M3 Types 7378

Бренд: IBM Страницы: 45

Бренд: IBM Страницы: 214

Бренд: AIC Страницы: 88

ProLiant DL580 Gen10

Бренд: HPE Страницы: 158

SUPERSERVER 6015C-M3

Бренд: Supero Страницы: 118

SUPERSERVER 5014C-MT

Бренд: Supero Страницы: 112

Бренд: Brocade Communications Systems Страницы: 176

Бренд: Ekselans Страницы: 37

Бренд: Bosanova Страницы: 2

Бренд: Bosanova Страницы: 2

Бренд: Polycom Страницы: 2

Бренд: Black Box Страницы: 3

Бренд: IBM Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды