Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 168 | Manualshive

Страница: 168 / 313

background image

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is

solved.

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are customer replaceable

units (CRU) and which components are field replaceable units (FRU).

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

Trained service technician.

Error code

Description

Action

0051003

Uncorrectable runtime
DIMM error

1. Refer to TIP H21455 for minimum code level.

2. Check the IBM support website for an applicable retain tip or

firmware update that applies to this memory error.

3. Swap one of the DIMMs with a DIMM of the same size and type from

another channel (see “Installing a DIMM - BladeCenter HX5” on
page 104. For example, if a problem occurs on DIMM 1 and DIMM 4,
swap DIMM 1 with a similar DIMM in slot 9.

4. Enable all affected DIMMs using the Setup utility.

5. If the failure remains on the original DIMM slots, replace the DIMM

that was not moved. If the failure follows the DIMM that was moved,
replace the DIMM that was swapped.

6. If the problem occurs on the same DIMM connector, check the

DIMM connector. If the connector is damaged, (Trained service
technician only) replace the system-board assembly (see “Removing
the system-board assembly - BladeCenter HX5” on page 140 and
“Installing the system-board assembly - BladeCenter HX5” on page
142).

0051006

DIMM mismatch detected.

Make sure that the DIMMs match and have been installed in the correct
order (see “Installing a DIMM - BladeCenter HX5” on page 104).

If you receive this error code for a blade server configuration that
includes an IBM MAX5 expansion blade, multiple DIMMs might have
been disabled. After you replace the mismatched DIMM, make sure that
all DIMMs have been enabled using the Setup utility (see “Using the
Setup utility” on page 20) or using the Advanced Settings Utility (see
“Using the Advanced Settings Utility (ASU)” on page 25).

152

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

«
...
166
167
168
169
170
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

Бренд: IBM Страницы: 40

Бренд: Lantech Страницы: 49

Absolute Stream

Бренд: Ideon Audio Страницы: 24

Бренд: Discover Video Страницы: 148

RuggedJet RJ-4040

Бренд: Brother Страницы: 111

Бренд: Brother Страницы: 253

Бренд: Dell Страницы: 77

Бренд: Dell Страницы: 14

Бренд: Dell Страницы: 116

PowerEdge FC430

Бренд: Dell Страницы: 102

Бренд: Dell Страницы: 188

Бренд: Dell Страницы: 16

Бренд: Dell Страницы: 66

Бренд: Dell Страницы: 160

Бренд: Dell Страницы: 32

Бренд: Dell Страницы: 82

Бренд: Dell Страницы: 40

Бренд: Dell Страницы: 180

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды