Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 98

Страница: 98 / 313

Step 2. If the scalable blade complex is installed in a BladeCenter chassis, remove it (see “Removing the

blade server from the BladeCenter chassis” on page 66 for instructions).

Step 3. Carefully lay the blade server on a flat, static-protective surface.

Step 4. Open the blade server cover (see “Removing the blade server cover” on page 71 for instructions).

Step 5. Stand the blade server upright on a clean, flat work surface, with the scalability connector facing

up.

Step 6. Open the lower handle (rotate the lower handles down) to allow the blade server to sit flat on the

work surface.

Step 7. Using the 3/16" hex driver that comes with the 1-node speed burst card, loosen the nut that

attaches the 1-node speed burst card to the blade server.

Step 8. Lift the 1-node speed burst card off the blade server.

Step 9. If you are instructed to return the speed burst card, follow all packaging instructions, and use any

packaging materials for shipping that are supplied to you.

Installing the 1-node speed burst card

Use this information to install a 1-node speed burst card in a blade server.

To install a 1-node speed burst card, complete the following steps:

Alignment
pins

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. If the blade server or scalable blade complex is installed in a BladeCenter chassis, remove it. See

“Removing the blade server from the BladeCenter chassis” on page 66 for instructions.

Step 3. Carefully lay the blade server on a flat, static-protective surface.

Step 4. Open the blade server cover (see “Removing the blade server cover” on page 71 for instructions).

Step 5. If an optional expansion unit is installed, remove the expansion unit (see “Removing an expansion

unit” on page 96 for instructions).

Note:

Optional expansion units are not supported when a IBM MAX5 expansion blade is installed.

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды