Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 185

Страница: 185 / 313

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is

solved.

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are CRUs and which

components are FRUs.

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

trained service technician.

Type

Error Message

Action

Error

Proc/IO module 1, temperature (IOH
Temp) critical

1. Make sure that the room temperature is within the

operating specifications (see “Features and
specifications” on page 4).

2. Make sure that none of the air vents on the BladeCenter

chassis and on the blade server are blocked.

3. Make sure that all of the fans on the BladeCenter chassis

are running.

Error

System board, chip set (Sys Board
Fault) critical

1. Make sure that the latest firmware is being used (see

“Updating firmware and device drivers” on page 30).

2. Reset the UEFI firmware settings to default values using

the Setup utility (see “Using the Setup utility” on page 20).

3. Reseat the blade server in the BladeCenter chassis (see

“Removing the blade server from the BladeCenter
chassis” on page 66 and “Installing a blade server in a
BladeCenter chassis” on page 67).

4. (Trained service technician only) Replace the system-

board assembly (see “Removing the system-board
assembly - BladeCenter HX5” on page 140 and “Installing
the system-board assembly - BladeCenter HX5” on page
142).

Chapter 5

Diagnostics

169

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды