manualshive.com logo in svg

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Lenovo BladeCenter HX5 1909 - Проблема Определения И Служебное Руководство для скачивания бесплатно. Это руководство предоставляет важные сведения о разрешении проблем и обслуживании продукта. Скачайте его с manualshive.com и получите доступ к подробной информации о вашем устройстве.

Поделиться
Скачать
background image

Step 4.  Follow the instructions on the screen to change the settings of the selected items; then, press 

Enter

. If you select 

SAS Topology 

or 

Advanced Adapter Properties

, additional screens are 

displayed.

Updating firmware and device drivers

IBM periodically makes UEFI code, service processor (IMM) firmware, diagnostic firmware updates, and 
device driver updates available for the blade server. Several methods are available to update the firmware for 
the blade server.

If you are updating the firmware for the blade servers in a scalable blade complex operating in single partition 
mode, you only must update the firmware for the primary blade server. When you update the firmware for the 
primary blade server, the firmware for the secondary blade server is updated as well. Device drivers are 
updated through the operating system.

You can update the firmware and device drivers for the blade server by using one of the following methods. 

•  Using UpdateXpress System Packs. UpdateXpress System Packs (UXSP) contain an integration-tested 

bundle of online, updatable firmware and device drivers for your servers. For more information about 
UpdateXpress System Packs, see http://www.ibm.com/systems/ support/supportsite.wss/docdisplay?l 
ndocid=SERV-XPRESS&brandind=5000008

•  Using the IBM ToolsCenter Bootable Media Creator. You can use IBM ToolsCenter Bootable Media 

Creator to create bootable media that is suitable for applying firmware updates, running preboot 
diagnostics, and deploying Windows operating systems on supported systems. Using IBM ToolsCenter 
Bootable Media Creator, you can create a single bootable image on supported media (such as CD, DVD, 
ISO image, USB flash drive, or set of PXE files) that bundles multiple IBMBladeCenter tools and updates 
from UpdateXpress System Packs, which contain Windows and Linux® firmware and device-driver 
updates. You can also create an 

IBM ServerGuide Setup and Installation 

CD for deploying Windows 

operating systems and updates on supported systems. For more information about the Bootable Media 
Creator, see http://www.ibm.com/systems/support/ supportsite.wss/docdisplay? lndocid=TOOL- 
BOMC&brandind=5000008.

•  Downloading the firmware and device drivers from http://www.ibm.com/support/ fixcentral/systemx/ 

groupView? query.productGroup=ibm%2FBladeCenter. Follow the instructions that come with the 
firmware and device drivers to install them.You must make sure that you update the firmware for each 
blade server in the scalable blade complex to the same levels before resetting the scalable blade 
complex. Refer to the following table to select the correct procedure to follow based on your configuration 
and preferred update method: 

Table 2.  Procedures to update firmware for blade servers in a scalable blade complex

Scalable blade complex 
mode

Inband updates

Out-of-band updates

Single partition

“Updating firmware for blade servers 
operating as a single partition” on page 
31

“Updating firmware for each blade 
server independently” on page 31

Independent partitions

“Updating firmware for each blade 
server independently” on page 31

“Updating firmware for each blade 
server independently” on page 31

For more information about updating firmware and the preferred methods, see the Firmware Update Best 
Practices white paper at http://www-947.ibm.com/systems/support/supportsite.wss/docdisplay?lndocid= 
MIGR-5082923&brandind=5000020.

For additional instructions about updating the firmware before attaching a IBM MAX5 expansion blade, see 
http://www.ibm.com/support/entry/portal/docdisplay?lndocid=MIGR-5085756

30

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

Rack Solutions 122-2447 Installation Instructions Manual preview
122-2447
Бренд: Rack Solutions Страницы: 8
IntesisBox Modbus Server-FC330A Installation Manual preview
Modbus Server-FC330A
Бренд: IntesisBox Страницы: 5
H3C UniServer R4300 G5 Installation, Quick Start preview
UniServer R4300 G5
Бренд: H3C Страницы: 16
Cyclades Cyclades-PR4000 Installation Manual preview
Cyclades-PR4000
Бренд: Cyclades Страницы: 174
Supero SuperServer 6024H-82 User Manual preview
SuperServer 6024H-82
Бренд: Supero Страницы: 122
IBM 1-Port USB Print Server Hardware User'S Manual preview
1-Port USB Print Server
Бренд: IBM Страницы: 15
Fujitsu GP 7000F Manual preview
GP 7000F
Бренд: Fujitsu Страницы: 200
Arista NetVisor UNUM High Capacity Appliance User Manual preview
NetVisor UNUM High Capacity Appliance
Бренд: Arista Страницы: 81
Toshiba RS-TX60 Specification Sheet preview
RS-TX60
Бренд: Toshiba Страницы: 2
Toshiba BMS-LSV6E Installation Manual preview
BMS-LSV6E
Бренд: Toshiba Страницы: 8
Toshiba BMS-LSV6UL Installation Manual preview
BMS-LSV6UL
Бренд: Toshiba Страницы: 12
Toshiba BMS-LSV4E Installation Manual preview
BMS-LSV4E
Бренд: Toshiba Страницы: 8
Toshiba C1 Installation Manual preview
C1
Бренд: Toshiba Страницы: 16
Toshiba IPedge EP Server Product Bulletin preview
IPedge EP Server
Бренд: Toshiba Страницы: 19
Toshiba SD-H400 - Combination Progressive-Scan DVD Player Service Manual preview
SD-H400 - Combination Progressive-Scan DVD Player
Бренд: Toshiba Страницы: 53
Toshiba MAGNIA 510D User Manual preview
MAGNIA 510D
Бренд: Toshiba Страницы: 185
Toshiba Digital Media Server Viewer'S Manual preview
Digital Media Server
Бренд: Toshiba Страницы: 204
Toshiba Magnia 550D User Manual preview
Magnia 550D
Бренд: Toshiba Страницы: 241

Бренды по названию

Популярные бренды

Загрузить еще бренды