Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 313

background image

This amber LED indicates that there is a problem with the system board. If this amber LED is lit,
complete the following steps:

1. Install the IBM MAX5 (see “Installing an IBM MAX5 expansion blade” on page 88).

2. Install the BladeCenter HX5 in the chassis (see “Installing a blade server in a BladeCenter chassis”

3. Restart the blade server.

4. Check system-event and IMM/AMM logs related to memory and resolve those events (see “POST

error codes” on page 149 and “IMM error codes in AMM” on page 162).

5. If the problem remains, replace the system board on the IBM MAX5(see “Removing the system-

board assembly - BladeCenter HX5” on page 140 and “Installing the system-board assembly -
BladeCenter HX5” on page 142 for instructions).

The System Board (S BRD) LED is referred to as MEU Error in the system-event log.

Light path power (LP2)

This amber LED indicates that one or more LEDs are lit on the IBM MAX5 system board. See “Light path
diagnostics LEDs - IBM MAX5” on page 209 for additional information.See the

Problem Determination

and Service Guide

for additional information..

The Light path power (LP2) LED is referred to as MEU LED Power in the system event log.

See “Light path diagnostics LEDs - IBM MAX5” on page 209 for more information about the LEDs on the IBM
MAX5 expansion blade.

Scalability indicators

The BladeCenter HX5 blade server provides scalability indicators, which are viewable through the front bezel
of the blade server when it is installed in a BladeCenter chassis. The scalability indicators remain lit until the
blade server is started.

The BladeCenter HX5 blade server can be deployed as a stand-alone blade server. It can also be combined
with another BladeCenter HX5 blade server to form a scalable blade complex. When two BladeCenter HX5
blade servers are combined into a scalable blade complex, you can specify that they operate as a single
hardware partition or operate in stand-alone mode.

The scalability indicators show whether a BladeCenter HX5 blade server is a stand-alone blade server or a
node in a scalable blade complex operating as a single hardware partition.

When a BladeCenter HX5 blade server is a stand-alone blade server, the scalability indicators continually
move up and down the front of the bezel.

LEDs

10

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

«
...
24
25
26
27
28
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

Бренд: NAIM Страницы: 16

Бренд: Ganz Страницы: 5

UniServer R6900 G5

Бренд: H3C Страницы: 17

Бренд: Cable-Tronix Страницы: 33

Бренд: Ubiquiti Страницы: 28

Бренд: Arris Страницы: 6

Alcatel-Lucent OXO Connect Compact

Бренд: Nokia Страницы: 216

Proline Promass 500

Бренд: TechnipFMC Страницы: 32

FileStore N8300

Бренд: Symantec Страницы: 55

Бренд: Monoprice Страницы: 5

Бренд: 2Wire Страницы: 35

Бренд: EEG Страницы: 32

Бренд: Intel Страницы: 67

X38ML - Server Board Motherboard

Бренд: Intel Страницы: 132

XtremeServer 2544

Бренд: Uniwide Страницы: 98

Бренд: Lantronix Страницы: 30

Бренд: Qsan Страницы: 65

Бренд: Mackie Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды