Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 313

background image

A set of blank labels for your blade server comes with the BladeCenter chassis. When you install the blade
server in the BladeCenter chassis, write identifying information about the blade server on a label. Then place
the label on the BladeCenter chassis bezel. See the documentation for your BladeCenter chassis for
recommended label placement.

Important:

Do not place the label on the blade server itself or in any way block the ventilation holes on the

blade server.

In addition, the system service label, which is on the cover of the server, provides a QR code for mobile
access to service information. You can scan the QR code using a QR code reader and scanner with a mobile
device and get quick access to the IBM Service Information website. The IBM Service Information website
provides additional information for parts installation and replacement videos, and error codes for server
support.

The following illustration shows the QR code (http://ibm.co/114H7dt):

Figure 1. QR code

Related documentation

Use this information to identify and locate related blade server documentation.

This

Problem Determination and Service Guide

contains information to help you resolve problems yourself,

and it contains information for service technicians. The following documentation is also available:

•

Installation and User's Guide

This document contains general information about the blade server, including how to install supported
optional devices and how to configure the blade server.

•

Safety Information

This document contains translated caution and danger statements. Each caution and danger statement
that appears in the documentation has a number that you can use to locate the corresponding statement
in your language in the

Safety Information

document.

•

Warranty Information

This document contains information about the terms of the warranty.

•

Environmental Notices and User Guide

This document contains translated environmental notices.

•

Integrated Management Module User's Guide

This document explains how to use the functions of the IMM that is installed in an IBM server. The IMM
works with IBMSystem x Server Firmware to provide systems-management capability for System x and
BladeCenter servers.

•

Advanced Management Module User's Guide

This document provides information about configuring the advanced management module and managing
components that are installed in an IBM® BladeCenter® chassis.

•

Advanced Management Module Command-Line Interface Reference Guide

3

«
...
17
18
19
20
21
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

Univerge SV8100

Бренд: NEC Страницы: 2

Бренд: Oki Страницы: 121

Бренд: Vxl Страницы: 19

Бренд: Longshine Страницы: 56

RS/6000 7043 260

Бренд: IBM Страницы: 322

SuperServer 1026T-M3

Бренд: Supero Страницы: 104

Бренд: Thecus Страницы: 130

8676 - Eserver xSeries 335

Бренд: IBM Страницы: 172

FusionServer G5500 V6

Бренд: xFusion Digital Technologies Страницы: 100

SUPERSERVER 5014C-MT

Бренд: Supero Страницы: 112

SUPERSERVER 5018D-MF

Бренд: Supero Страницы: 120

Бренд: QUANTA Страницы: 177

DPR-1260 - RangeBooster G Multifunction Print Server

Бренд: D-Link Страницы: 55

Бренд: D-Link Страницы: 49

StorCenter Pro NAS 200rL

Бренд: Iomega Страницы: 2

Бренд: AIC Страницы: 86

Бренд: AIC Страницы: 97

Бренд: AIC Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды