Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 67

Страница: 67 / 313

Step 8. Restart the blade server (see “Turning on the blade server” on page 11). The system begins the

power-on self-test (POST).

Step 9. Boot the server to the operating system or the F1 UEFI configuration menu.

Step 10. Log into the Advanced Management's web interface.

Step 11. After you log in, select

MM Control -> Network Protocol

and ensure that TFTP is enabled on the

management module. The default setting is disable.

Step 12. Select

Blade Tasks -> Firmware update

and select the blade server you want to recover.

Step 13. Use the browse button to point to the UEFI update file.

Step 14. Click the

Update

button to update the UEFI firmware.

Step 15. Reboot the server and verify that it completes POST (see “Turning off the blade server” on page 12

and “Turning on the blade server” on page 11).

Step 16. Turn off the server (see “Turning off the blade server” on page 12).

Step 17. Remove the blade server form the BladeCenter unit (see “Removing the blade server from the

BladeCenter chassis” on page 66).

Step 18. Remove the server cover. See “Removing the blade server cover” on page 71.

Step 19. Move the UEFI boot block recovery switch (SW2-7) to the OFF position (see “System-board

switches” on page 13).

Step 20. Replace the cover and reinstall the blade server in the BladeCenter unit, making sure that the media

tray is selected by the relevant blade server. See “Installing the blade server cover” on page 73 and
“Installing a blade server in a BladeCenter chassis” on page 67.

Step 21. Restart the blade server (see “Turning off the blade server” on page 12 and “Turning on the blade

server” on page 11). The system begins the power-on self-test (POST). If this does not recover the
primary bank continue with the following steps.

Step 22. Remove the blade server form the BladeCenter unit (see “Removing the blade server from the

BladeCenter chassis” on page 66).

Step 23. Remove the server cover. See “Removing the blade server from the BladeCenter chassis” on page

66.

Step 24. Reset the CMOS by removing the battery (see “Removing the battery” on page 76).

Step 25. Leave the battery out of the server for 5 minutes.

Step 26. Reinstall the battery (see “Installing the battery” on page 77).

Step 27. Replace the cover and reinstall the blade server in the BladeCenter unit, making sure that the media

tray is selected by the relevant blade server. See “Installing the blade server cover” on page 73 and
“Installing a blade server in a BladeCenter chassis” on page 67.

Step 28. Restart the blade server (see “Turning on the blade server” on page 11).

The system begins the power-on self-test (POST).

In-band automated boot recovery method

To download the server UEFI firmware update package from the World Wide Web, complete the following
steps.

Note:

Use this method if the SYS BRD LED on the light path diagnostics panel is lit and there is an AMM

event log entry or Booting Backup Image is displayed on the firmware splash screen; otherwise, use the in-
band manual recovery method.

Step 1. Download the blade server UEFI firmware update from the World Wide Web (see “Updating

firmware and device drivers” on page 30).

Chapter 2

Configuring the blade server

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды