manualshive.com logo in svg

Kikusui KHA3000, Руководство по эксплуатации, Страница: 386 / 392

Поделиться
Скачать
Kikusui KHA3000 Скачать руководство пользователя страница 386

Troubleshooting

386

KHA3000

Measurement failure

Report printing failure

Symptom

Check item/Corrective action

Page

Measured values seem wrong.

•

Is an appropriate measurement circuit used?
Perform measurement using the measurement circuit required 
by the standard.

54

•

Synchronization with the AC power supply is probably not 
established.

•

Is the triangular waveform of the PLL icon still on the screen?
Turn on OUTPUT of the AC power supply.
Set the correct frequency for the AC power supply.

118
203

•

Is the voltage sensing terminal wired?

57

•

Is the scaling correctly set?
Check the setting of PT Ratio for the PT (potential transformer) 
being used.
Check the setting of CT Ratio for the CT (current transformer) 
being used.
Check the setting of EXT CS Ratio for the external sensor being 
used.

106
197
258

•

Is the phase difference with the external sensor correctly 
adjusted?
Check the setting of V/I phase difference adjustment for the 
external sensor being used.

•

Are the Voltage CF and Current CF correctly set?
Set the CF values correctly so that the peak values can be 
measured correctly without the effect of any distortion.

EUT does not work.

•

Is OUTPUT of the AC power supply set to ON?
Check the control signal cable of the AC power supply.

118
203

•

Is the control signal cable of the AC power supply connected?

66

See

Symptom

Check item/Corrective action

Page

Reports cannot be printed.

•

Is the limit value set to 3rd/5th/Current Wave?
When 3rd/5th/Current Wave is selected, you cannot print 
reports. Use the SD006-KHA application software to print the 
reports.

－

See

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов