manualshive.com logo in svg

Kikusui KHA3000, Руководство по эксплуатации, Страница: 228 / 392

Поделиться
Скачать
Kikusui KHA3000 Скачать руководство пользователя страница 228

228

KHA3000

Test Ending Menu

AC Power Supply OUTPUT OFF

Turn off the power to the EUT.

1

Press the F5 key to select AC Power Supply OUTPUT OFF.

The  output of the  AC  power supply will be turned  off.  The bulb  icon at the top of the
display will be turned off.

Using EXT CONT

An alternative method to turn off the AC power supply output is described below:

1

Press the EXT CONT key.

The External Control display appears.

2

Press the F1 key to select AC Power Supply Control.

A sub-menu is displayed.

3

Press the F1 key to select OFF in OUTPUT.

OUTPUT of the AC power supply is set to OFF. The lamp icon in the upper part of the
screen goes out.

4

Press the F6 key to return.

F1

Save

F2

Report Print

Sub Menu

F3

Exit

F4

Analysis (VIEW)

→

F5

AC Power Supply
OUTPUT OFF

Menu 1/1

18

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов