manualshive.com logo in svg

Kikusui KHA3000, Руководство по эксплуатации, Страница: 350 / 392

Поделиться
Скачать
Kikusui KHA3000 Скачать руководство пользователя страница 350

350

KHA3000

Cleaning and Checking

Periodic  cleaning  and  checking  are  required  for  maintaining  the  initial  performance  of  this
product for a long period.

Cleaning the panel surface

If the panel surface is dirty, wipe it lightly with a soft cloth dampened with neutral detergent
diluted with water.

Checking the power cord

Check the power cord for covering breakage, plug damage and backlash.

Replacing the Backup Battery

This  product  contains  an  internal  battery.  Although  the  service  life  of  the  battery  varies
depending  on  the  operating  environment,  the  reference  service  life  is  two  years  after
purchase. For battery replacement, contact your Kikusui agent or distributor.
This  product  comes  with  an  installed  CR  Coin  Lithium  Battery  which  contains  Perchlorate
Material. Disposal of this battery may be regulated due to environmental considerations.
See www.dtsc.ca.gov/hazardouswaste/perchlorate

Replacing a Fuse

1

Turn off the POWER switch and unplug the power cord.

WARNING

•

There is a risk of death or injury caused by an electric shock. Be sure to turn off the 
POWER switch and unplug the power cord.

CAUTION

•

Do not use volatile matters such as thinner or benzene. Using these materials may cause 
surface discoloration, deletion of printed characters, or whitening of the display.

WARNING

•

To prevent an electric shock, unplug the power cord of this product before replacing 
a fuse.

•

Use a fuse with the suitable shape, rating, and characteristics for this product.

•

Using a fuse with an invalid rating or a short-circuited fuse holder is dangerous. 
Never do it.

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов