Kikusui KHA3000 Скачать руководство пользователя страница 305

Страница: 305 / 392

KHA3000

305

Harmonic Measurement Mode (61000-3-2)

Rem

ote Contr

Command

HARMonics:IEC32:FUNDamental:DEFinition {MEASured|SPECified}

HARMonics:IEC32:FUNDamental:DEFinition?

Parameter Value:

MEASured

Measured value (default)

SPECified

Specified value

Response

Returns the fundamental current value and the specification method of the power factor in
the <character> format.

HARM:IEC32:FUND:CURR

Sets the specified value of the fundamental current for Class C.

Command

HARMonics:IEC32:FUNDamental:CURRent{<numeric>|MIN|MAX}

HARMonics:IEC32:FUNDamental:CURRent?

Parameter Value:

0.0 to 75.0 (The default is 20.0.)

Unit:

Response

Returns the specified value of the fundamental current in the <NR3> format.

HARM:IEC32:FUND:PFAC

Sets the specified value of the power factor for Class C.

Command

HARMonics:IEC32:FUNDamental:PFACtor{<numeric>|MIN|MAX}

HARMonics:IEC32:FUNDamental:PFACtor?

Parameter Value:

0.00 to 1.00 (The default is 1.00.)

Unit:

None

Response

Returns the specified value of the power factor in the <NR3> format.

HARM:IEC32:LVT

Sets the limit value to be applied for Class C.

Command

HARMonics:IEC32:LVTable

{NORMal|CLASSA|CLASSD|WJUDge|THDLimit}

HARMonics:IEC32:LVTable?

Parameter Value:

NORMal

Normal limit value (default)

CLASSA

Limit value of Class A

CLASSD

Limit value of Class D

WJUDge

3rd/5th/Current Wave

THDLimit

THD limit (valid only when IEC 61000-3-2 Ed5.0 is selected)

Response

Returns the limit value to be applied in the <character> format.

** RST

RST

** RST

RST

** RST

RST

Содержание KHA3000









































































































































































































































































































































































































Результаты поиска

Содержание KHA3000

Отзывы:

Kikusui KHA3000, Руководство по эксплуатации, Страница: 305 / 392

Результаты поиска

Содержание KHA3000

Отзывы: