manualshive.com logo in svg

Kikusui KHA3000, Руководство по эксплуатации, Страница: 137 / 392

Поделиться
Скачать
Kikusui KHA3000 Скачать руководство пользователя страница 137

6

KHA3000

137

Setting Test Conditions (61000-3-12)

Executing Harm

onic Tests

7

Press the F6 key to return.

8

Press the F6 key to select menu page 3/4.

9

Press  the  F1  key  to  select  Specified  in  Reference  Current/Reference
Fundamental Current.

10

Press  the  F2  key  to  input  a  reference  current  specigication/reference
fundamental current specification.

The input range is 0.0 A to 75.0 A.

Inputting Comments for Report Printing

1

Press the HA key.

The HA-Test Conditions List display appears.

2

Press the F6 key to select menu page 2/4.

3

Press the F3 key to select Comment Input.

A sub-menu is displayed.

4

Input comments for the menu items.

p. 114

The input comments can be checked on the screen.

5

Press the F6 key to return.

Checking the Third, Fifth and Seventh Harmonics

1

Press the VIEW key.

The HA-Observation and Analysis display appears.

p. 169

2

Press the F6 key to select menu page 1/2.

3

Press the F1 key to select Harmonics List in View Type.

The harmonics list of measured values is displayed.

4

Press the F2 key to select View Setting.

A sub-menu is displayed.

5

Press the F4  key to select In/Iref [%] or In/I1 [%] in Measurement Value
Selection.

6

Press the F5 key to select L1 in Check View Phase.

Select the L1 phase first. Make checks for each phase by the following procedure.

7

Check that the largest third harmonic current value is less than 5% of the
reference current value/reference fundamental current value.

Check for each phase.

See

See

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов