Kikusui KHA3000 Скачать руководство пользователя страница 304

Страница: 304 / 392

304

KHA3000

Harmonic Measurement Mode (61000-3-2)

Setting the Class of the EUT

HARM:IEC32:CLAS

Sets the class of the EUT. The reference value for determining conformance to the standard
is the limit value corresponding to the class.

Command

HARMonics:IEC32:CLASs “{A|B|C|D}”

HARMonics:IEC32:CLASs?

Parameter Value:

“A”

Class A (default)

“B”

Class B

“C”

Class C

“D”

Class D

Response

Returns the class of the EUT in the

<“string”>

format.

Class A Condition (JIS C61000-3-2)

HARM:IEC32:CONS600

When the EUT is in Class A, sets whether or not the air conditioner exceeds the effective
input power of 600 W.

Command

HARMonics:IEC32:CONSider600{ON|OFF|1|0}

HARMonics:IEC32:CONSider600?

Parameter Value:

ON(1)

Yes

OFF(0)

No (default)

Response

Returns whether or not the air conditioner exceeds the effective input power of 600 W in the
<NR1> format.

Class C Conditions

HARM:IEC32:FUND:DEF

Sets the fundamental current value and the specification method of the power factor
(measured or specified value) for Class C.

** RST

RST

** RST

RST

** RST

RST

Содержание KHA3000









































































































































































































































































































































































































Результаты поиска

Содержание KHA3000

Отзывы:

Kikusui KHA3000, Руководство по эксплуатации, Страница: 304 / 392

Результаты поиска

Содержание KHA3000

Отзывы: