Kikusui KHA3000 Скачать руководство пользователя страница 336

Страница: 336 / 392

336

KHA3000

System Setting

SYST:VERS

Queries the version of the SCPI specifications with which this product is compliant.

Command

SYSTem:VERSion?

Response

Always returns 1999.0.

SYST:CONF:LANG

Sets the type of language.

Command

SYSTem:CONFigure:LANGuage {ENGLish|JAPanese}

SYSTem:CONFigure:LANGuage?

Parameter Value:

ENGLish

English

JAPanese

Japanese

Response

Returns the language type in the <character> format.

SYST:CONF:PCR

Specifies whether or not to enable AC Power Supply control.

Command

SYSTem:CONFigure:PCR[:STATe] {ON|OFF|1|0}

SYSTem:CONFigure:PCR[:STATe]?

Parameter Value:

ON(1)

Enable

OFF(0)

Disable (default)

Response

Returns information on whether or not to enable AC Power Supply control in the <NR1>
format.

SYST:CONF:TEXT:ENC

Sets the character code used for encoding when a comment text is set by a command.

Command

SYSTem:CONFigure:TEXT:ENcoding <string>

SYSTem:CONFigure:TEXT:ENcoding?

Parameter Value:

“Shift-JIS”

Response

Returns the character code used for encoding in the <string> format.

Содержание KHA3000









































































































































































































































































































































































































Результаты поиска

Содержание KHA3000

Отзывы:

Kikusui KHA3000, Руководство по эксплуатации, Страница: 336 / 392

Результаты поиска

Содержание KHA3000

Отзывы: