manualshive.com logo in svg

Kikusui KHA3000, Руководство по эксплуатации, Страница: 124 / 392

Поделиться
Скачать
Kikusui KHA3000 Скачать руководство пользователя страница 124

124

KHA3000

Setting Test Conditions (61000-3-2)

Set  the  test  conditions  with  the  HA-Test  Conditions  List  display.  When  the  test  condition
setting is complete, switch to the HA-Observation and Analysis display for observation during
the test.

Setting Limit Value and Measuring Technique Standards

1

Press the HA key.

The HA-Test Conditions List display appears.

2

Select test conditions.

p. 267

To use the same conditions as for a test that was executed in the past, call up a test
condition file and use it.

3

Press the F6 key to select menu page 1/4.

4

Press the F1 key to select Limitation Standard.

Select IEC 61000-3-2 Ed5.0, IEC 61000-3-2 Ed3.0, IEC 61000-3-2 Ed2.2, JIS C 61000-
3-2 2005 or JIS C 61000-3-2 2019.

5

Press the F2 key to select Measuring Technique Standard.

To  employ  a  measuring  method  for  harmonic  groups,  select  IEC 61000-4-7  Ed2.0  or
IEC 61000-4-7 Ed2.1.

6

Press  the  F6  key  to  switch  to  another  menu  page  and  set  other  test
conditions.

See

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов