Kikusui KHA3000 Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 392

Kikusui KHA3000 Скачать руководство пользователя страница 80

80

KHA3000

Switching Displays

Keys Used to Display the System Setup Display and Other

Displays

Dedicated keys are used respectively to display the following displays:

•

System Setup display: SYSTEM key

•

Other Measurement displays: OTHER key

•

File Operation display: FILE key

•

External Control display: EXT CONT key

•

Assist display: ASSIST key



System Setup Display and Other Displays

Name and contents

Example

System Setup display

Setting common items
Communication interface,
buzzer volume,
date and time, etc.

* The option information shown
is an example

Other Measurement display

Basic measurement
FFT analyzer
In-rush current measurement

File Operation display

Calling the test condition file
(load)
Calling the test result file (load)
Saving the test condition file
(save)
Calling the scaling setting
condition (load)

«
...
78
79
80
81
82
...
»

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов