manualshive.com logo in svg

Kikusui KHA3000, Руководство по эксплуатации, Страница: 85 / 392

Поделиться
Скачать
Kikusui KHA3000 Скачать руководство пользователя страница 85

4

KHA3000

85

Key Used to Lock Operation, and Other Keys

System

 Setup

Holding the Display

�

Press the HOLD key.

Measured  values  and  graphics  in  the  display  are  left  unchanged.  With  the
measurement  active,  only  the  view  display  is  held  still.  This  key  is  used  to  monitor
changes, detect abnormal values, and determine the view to be output to the printer.

Saving the Current Display

�

Press the HARD COPY key.

The  hard  copy  dialog  box  is  displayed.  The  display  is  saved  to  the  external  memory
CompactFlash card or USB flash drive. A file name is automatically created. When the
saving is finished, the hard copy dialog box disappears.
This function cannot be used during the test.

Changing the Display Brightness

�

Press the BACK LIGHT (SHIFT + Up/Down Arrow) key.

The Up Arrow increases the brightness. The Down Arrow decreases the brightness.

Changing the Buzzer Volume

�

Press the BUZZER (SHIFT + 1) key or (SHIFT + 0).

Pressing the 1 key turns up the volume, and pressing the 0 key turns down the volume.

Changing to Local Operation

�

Press the LOCAL key.

Remote control operation is finished and key operation is enabled (the REMOTE LED is
turned off).
When the remote control is active, the REMOTE LED is ON.

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов