Kikusui KHA3000 Скачать руководство пользователя страница 286 | Manualshive

Страница: 286 / 392

Kikusui KHA3000 Скачать руководство пользователя страница 286

286

KHA3000

Overview of Messages

Alternatives

When a numeric parameter is used with this product, MINimum and MAXimum are defined
for alternatives.
The following example sets the current range to the minimum value:

CURRent:RANGe MINimum

The maximum value or minimum value can be queried using a query for most parameters.

CURRent:RANGe? MIN

CURRent:RANGe? MAX

Measurement unit

The following default units are used. Values are accepted regardless of whether or not a
measurement unit is specified.

•

A (current)

•

V (voltage)

•

W (power)

•

S (seconds)

•

PCT (%)

•

HZ (frequency)

•

DEG (degree)

The following optional symbols are supported. Use

“

U

”

instead when coding

“



”

in the

parameter.

•

M (milli)

•

K (kilo)

•

U (micro)

The SI unit system includes lower-case letters in unit symbols. The IEEE standard specifies
upper-case letters. SCPI does not distinguish between upper-case and lower-case letters.

«
...
284
285
286
287
288
...
»

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов