Kikusui KHA3000 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 392

Kikusui KHA3000 Скачать руководство пользователя страница 72

72

KHA3000

Turning On the Power

This section explains how to turn on the power to this product independently, and then
explains how to turn on the power to the test system including the AC power supply.

Turning On the POWER Switch

1

Turn the POWER switch to ON ( ).

Depress the POWER switch ( ). With the startup sound, all LEDs illuminate and the
firmware version is displayed. The built-in cooling fan starts to rotate.

2

Check the firmware version on the screen.

After the firmware version is displayed for several seconds, the harmonic current test
display (HA-Observation and Analysis display) appears.

3

Allow a sufficient warm-up period before starting the test.

See

«
...
70
71
72
73
74
...
»

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов