Kikusui KHA3000 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 392

Kikusui KHA3000 Скачать руководство пользователя страница 2

2

KHA3000

This document is intended for those who use this product for
the first time, and contains its overview, notes on various
settings, measuring methods, SCPI commands, maintenance,
and usage.

Read this manual thoroughly to ensure effective use of this
product

’

s functions. This manual will also be helpful if you

forget how to operate the product during use, or if a problem
occurs.

Applicable firmware version of product

This manual applies to products containing version 3.5X
firmware.

Before contacting the Kikusui distributor/agent for inquiries
about the product, please make a note of the following:

Type name (indicated at the upper part of the front panel)
Firmware version (see page 72)
Serial number (indicated at the lower part of the rear panel)

Intended reader of this manual

This manual is intended for those who use the harmonic/flicker
analyzer KHA3000 and those who teach operators how to use
it.

Explanations are given under the presumption that the reader
has electrical knowledge related to harmonic current and
voltage fluctuation tests.

When the SCPI commands are used, the reader is assumed
to have sufficient basic knowledge for controlling measuring
instruments using a PC.

Trademarks

Microsoft,  Windows  and  Visual  Basic  are  registered
trademarks  of  Microsoft  Corp.  Other  company  and  product
names  are  trademarks  or  registered  trademarks  of  the
respective companies.

Copyright and issuance

Reproduction and reprinting of this operation manual, in whole
or in part, without our permission is prohibited.

Both unit specifications and manual contents are subject to
change without notice.

© 200

9 Kikusui Electronics Corporation

For the safe use and safe maintenance of this product, the
following symbols are used throughout this manual and on the
product. Note the meaning of each of the symbols to ensure
safe use of the product. (Not all symbols may be used.)

or

Indicates that a high voltage (over 1000 V) is used here.
Touching the part may cause a possibly fatal electric
shock. If physical contact is required for your work,
start work only after you make sure that no voltage is
output here.

DANGER

Indicates an imminently hazardous situation that, if any
mishandling occurs by ignoring this indication, will
result in death or serious injury.

WARNING

Indicates a potentially hazardous situation that, if any
mishandling occurs by ignoring this indication, will
result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation that, if any
mishandling occurs by ignoring this indication, will
result in damage to the product and other property.

About This Manual

Shows that the act indicated is prohibited.

Indicates a danger, warning, or caution, or
details on it. If this mark is displayed on the
product, see the relevant sections in this manual.

Protective conductor terminal.

Chassis (frame) terminal.

ON (power).

OFF (power).

In position of a bi-stable push control

Out position of a bi-stable push control

Safety Symbols

«
1
2
3
4
...
»

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов