Kikusui KHA3000 Скачать руководство пользователя страница 306

Страница: 306 / 392

306

KHA3000

Harmonic Measurement Mode (61000-3-2)

Class D Conditions

HARM:IEC32:POW:DEF

Sets the type of power value for Class D. The type and the default of the value vary
corresponding to the test standard.

Command

HARMonics:IEC32:POWer:DEFinition

{MEASured|SPECified}

HARMonics:IEC32:POWer:DEFinition?

Parameter Value:

MEASured

Measured value (default)

SPECified

Specified value

Response

Returns the type of power value in the <character> format.

HARM:IEC32:POW

Sets the specified value of the power.

Command

HARMonics:IEC32:POWer[:LEVel]{<numeric>|MIN|MAX}

HARMonics:IEC32:POWer[:LEVel]?

Parameter Value:

0 to 135000 (The default is 100.)

Unit:

Response

Returns the value specified for the power in the <NR3> format.

** RST

RST

** RST

RST

Содержание KHA3000









































































































































































































































































































































































































Результаты поиска

Содержание KHA3000

Отзывы:

Kikusui KHA3000, Руководство по эксплуатации, Страница: 306 / 392

Результаты поиска

Содержание KHA3000

Отзывы: