manualshive.com logo in svg

Kikusui KHA3000, Руководство по эксплуатации, Страница: 207 / 392

Поделиться
Скачать
Kikusui KHA3000 Скачать руководство пользователя страница 207

9

KHA3000

207

Ex

ecuting V

olta

g

e Fluctuation T

ests

Setting the Impedance and AC Power Supply

The following procedure is common to the 61000-3-3 and 61000-3-11 standards.

1

Set the impedance.

See "Setting the Impedance" below.

2

Press the EXT CONT key.

The External Control display appears.

3

Press the F1 key to select AC Power Supply Control.

A sub-menu is displayed.

4

Press  the  F2  and  F3  keys  to  set  the  output  voltage  and  frequency
respectively.

p. 204

Set the AC power supply voltage and frequency according to the rated power of the EUT.

5

Set OUTPUT of the AC power supply to ON.

OUTPUT of the AC power supply is set to ON. The lamp icon in the upper part of the
screen lights up.
When it is synchronized with the frequency of the AC power supply, the triangular wave
in the PLL icon in the upper part of the screen becomes still.

6

Press the F6 key to return.

7

Turn on the power to the EUT.

Setting the Impedance

61000-3-3

Set to  the reference  impedance. The Line Impedance  Network  can  be  used;  for  details on
how to select the impedance, refer to the Operation Manual of the Line Impedance Network.

•

0.40 

 + jn0.25 

 (single-phase)

•

0.24 

 + jn0.15 

 (three-phase)

•

0.16 

 + jn0.10 

 (three-phase neutral line)

61000-3-11

Customers are asked to prepare the impedance.

●

When  you  declare  that  the  power  supply  to  be  connected  requires  a  current
capacity of 100 A or more per phase as the operating condition of the equipment

•

0.25 

 + jn0.25 

 (single-phase)

•

0.15 

 + jn0.15 

 (three-phase)

•

0.10 

 + jn0.10 

 (three-phase neutral line)

●

When  you  declare  the  maximum  permissible  system  impedance  (Zmax)  of  the
power supply to be connected as the operating condition of the equipment

•

The voltage drop caused by the EUT is 3% to 5% of the voltage.

•

The ratio of the reactance component to the resistance component of the impedance is

0.5 to 0.75.

See

If the triangular wave in the PLL icon does not become still

AC power supply

Check whether it is output correctly.

Wiring

Check whether the plug for the voltage-sensing terminal is set and 

connected to the VOLTAGE SENSING terminal on the rear.

Frequency

The PLL lock frequency range is 45 Hz to 65 Hz.

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов