Kikusui KHA3000, Руководство по эксплуатации, Страница: 371 / 392

KHA3000
371
Appx
Messages
FETC[:SCAL] | READ[:SCAL] | MEAS[:SCAL]
:CURR
:AMPL:MAX
– – A – NR3 –
Queries the measured value of
maximum current (positive
amplitude peak value).
R 3
:AMPL:MIN
– – A – NR3 –
Queries the measured value of
minimum current (negative
amplitude peak value).
R 3
:HARM[:AM
PL]
– – A – NR3 –
Queries the measured value of
harmonic current.
R 3
:HARM:THDI – –
PCT
– NR3 – Queries the measured THDI. R 3
:HARM:THD
F
– –
PCT
– NR3 – Queries the measured THDF. R 3
:HARM:PHA
S
– –
DEG
– NR3 –
Queries the phase angle of
harmonic current.
R 3
:FLIC:ST – – – – NR3 – Queries the momentary flicker value. R 3
:FREQ – – HZ – NR3 – Queries the set value for frequency. R 3
:PHAS:VOLT – –
DEG
– NR3 – Queries the phase angle of voltage. R 3
:POW:AC
[:REAL] – – W – NR3 –
Queries the measured value of
real power.
R 3
:APP – – VA – NR3 –
Queries the measured value of
apparent power.
R 3
:REAC – – VAR – NR3 –
Queries the measured value of
reactive power.
R 3
:PFAC – – – – NR3 – Queries the power factor. R 3
:VOLT
:AC – – V – NR3 –
Queries the measured value of AC
voltage (effective value).
R 3
:AMPL:MAX – – V – NR3 –
Queries the measured value of
maximum voltage (positive
amplitude peak value).
R 3
:AMPL:MIN – – V – NR3 –
Queries the measured value of
minimum voltage (negative
amplitude peak value).
R 3
ABOR[:ALL] – – – – – – Aborts a test. W 1
INIT[:IMM]
[:SEQ[1]] char – – – – – Starts a test (trigger function). W 1
:SEQ2 char – – – – – Starts in-rush current measurement. W 1
:SEQ3 char – – – – –
Starts testing when IEC 61000-3-3
(ManualSW) is selected in the limit
value standard for the voltage
fluctuation test.
W 1
:NAME char ACQ – – – – Starts a test (trigger function). W 1
INI:CONT
[:SEQ[1]] bool ON | OFF – OFF NR1 Sets the automatic continuation
mode (ON/OFF) of sequence
operation. R/W 3
:NAME char, bool
ACQ, ON |
OFF
– OFF NR1 R/W 3
TRIG
[:SEQ[1]] | [:ACQ]
:SOUR char IMM | BUS IMM char Sets the trigger source. R/W 3
SEQ2 | RUSH
:SOUR char IMM | BUS IMM char Sets the trigger source. R/W 3
:LEV numeric 0.1 to 80 A 0.1 NR3 Trigger level of current R/W 3
:CHAN NRf 1, 2, 3 – 1 NR3
Input phase (channel) used as a
trigger
R/W 3
SEQ3 | TEST
[:IMM] char TEST – – – –
Starts testing when IEC 61000-3-3
(ManualSW) is selected in the limit
value standard for the voltage
fluctuation test.
W 3
:SOUR char IMM | BUS IMM char Sets the trigger source. R/W 3
JUDG:RES – – – – char –
Queries the general judgment
result of the test that was finished
previously.
R 3
SCPI command Setting
Default
Response Influence
Description R/W
Note
Program header
Parameter Unit