Kikusui KHA3000 Скачать руководство пользователя страница 203

Страница: 203 / 392

KHA3000

203

Setting the Voltage Fluctuation Test

Controlling the AC Power Supply

The AC power sources that this product can directly control are PCR-LE and PCR-LA

. PCR-

WE is controlled by the separately sold application software SD006-KHA Harmonics
Analyzing Suite.

Setting the AC Power Supply

To establish communication with the AC Power Supply, set the communication parameters
from the AC power supply panel as shown below.

Showing the External Control Display

�

Press the EXT CONT key.

The External control display appears.

PCR-LA with firmware version 3.32 or 3.33 cannot be used.

PCR-LE

PCR-LA

A shaded area indicates
a set value.

Baudrate:

9600 bps/ 19200 bps/ 38400 bps

Data:

8 bits / 7 bits

Stop:

1 bit / 2 bits

Parity: None

(fix)

Flow Ctrl:

OFF / RTS

･

CTS

0 8 1 1

A shaded area indicates
a set value.

Baud rate

1: 9 600 bps

2: 19200 bps

Data length

7: 7 bits

8: 8 bits

Parity

0: None

1: Odd

2: Even

number

Stop bit

1: 1 bit

2: 2 bits

WARNING

•

To prevent an electric shock, do not touch the SOURCE and LOAD terminals of this
product.

•

Do not touch the OUTPUT terminal of the AC Power Supply.

•

Do not touch the INPUT and OUTPUT terminals of the Line Impedance Network.

Содержание KHA3000









































































































































































































































































































































































































Результаты поиска

Содержание KHA3000

Отзывы:

Kikusui KHA3000, Руководство по эксплуатации, Страница: 203 / 392

Результаты поиска

Содержание KHA3000

Отзывы: