Husqvarna F2303Q0 Скачать руководство пользователя страница 198

Страница: 198 / 322

17 ENGINE

Info

After replacing the crankshaft bearings, the crankshaft

end play must be measured.

Finishing work

- Measure the crankshaft end play. (

p. 198)

17.4.13 Changing the connecting rod, conrod bearing, and crank pin

310046-10

310071-10

196

Main work

- Position the crankshaft with special tool

in the press.

I Separator plate (79429009000)

(

p. 305)

- Press the crank pin out of the upper crankweb with special

tool@.
I Crankshaft pressing tool (75029047000) (

p. 301)

•

Info

Hold the lower crankweb.

- Remove the connecting rod and bearing.

- Press crank pin

out of the lower crankweb.

- Place the crankweb onto special tool

C,.

Insert for crankshaft pressing tool (79429008000)

(

p. 305)

Info

The special tool must be positioned with the flat sur

face facing downward.

- Press in new crank pin

all the way.

✓ Oil channel

is aligned with oil channel Cs).

X If the oil channels are not correctly aligned, the conrod

bearing will not be supplied with oil.

- Blow compressed air through the oil channels to check that

they are clear.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды