Husqvarna F2303Q0 Скачать руководство пользователя страница 98

Страница: 98 / 322

11 AIR FILTER

11.3

Note

Removing the air filter box cover

Pull off the air filter box cover sideways in areas f),

and

(D,

and remove toward the front.

Installing the air filter box cover

Removin the air filter

Position air filter box cover on collar bushings

and

and push toward the rear.

Engage the air filter box cover in areas f),

and

(D.

Engine damage

Unfiltered intake air has a negative effect on the service life of the engine.

Dust and dirt will enter the engine without an air filter.

Never start to use the vehicle without an air filter.

Note

Environmental hazard

Hazardous substances cause environmental damage.

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Preparatory work

Remove the air filter box cover. (

�

p. 96)

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды