Husqvarna F2303Q0 Скачать руководство пользователя страница 39

Страница: 39 / 322

-0

T02862-10

FORK, TRIPLE CLAMP 6

- Warm up the outside fork tube in area

of the lower

slide bearings.

Guideline

(122 °F)

- Hold the lower slide bearing with the longer side of the

special tool.

I Mounting tool (T14040S) (

ll!:!l

p. 311)

- Slide on the outside fork tube.

- Press the slide bearing all the way into the outside fork

tube.

- Position the support ring.

- Hold the seal ring with the shorter side of the special tool.

I Mounting tool (T14040S) (!alp. 311)

- Press the seal ring and support ring all the way into the

outside fork tube.

- Mount lock ring

✓ The lock ring engages audibly.

- Mount dust boot

- Assemble the individual components that belong

together.

Info

Shock absorber cartridge (right fork leg): cartridge

with silver adapter (9, axle clamp without brake

mount, and outside fork tube without warning

label, rebound adjuster

@).

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды