Husqvarna F2303Q0 Скачать руководство пользователя страница 128

Страница: 128 / 322

14 WHEELS

14.8.3

Changing the rear brake disc

Info

If the brake discs are changed, the brake linings must also be changed.

Preparatory work

- Raise the motorcycle with a lift stand. (

p. 12)

- Remove the rear wheel. (

p. 124)

Main work

- Remove screws

Remove the brake disc.

- Clean the contact surface of the brake disc.

- Position the new brake disc with the label facing outward.

- Mount and tighten screws

Guideline

Screw, rear

brake disc

14 Nm (10.3 lbf ft)

Loctite

243

™

Finishing work

- Install the rear wheel. (

p. 125)

- Remove the motorcycle from the lift stand. (

p. 12)

...

14.8.4

Checking the chain tension

126

Warning

Danger of accidents

Incorrect chain tension damages components and results in accidents.

If the chain is tensioned too much, the chain, engine sprocket, rear sprocket, transmission and rear

wheel bearings wear more quickly. Some components may break if overloaded.

If the chain is too loose, the chain may fall off the engine sprocket or the rear sprocket. As a result, the

rear wheel locks or the engine will be damaged.

- Check the chain tension regularly.

- Set the chain tension in accordance with the specification.

Preparatory work

- Raise the motorcycle with a lift stand. (

p. 12)

Main work

- Pull the chain at the end of the chain sliding piece upward to

measure chain tension

Info

Lower chain section

must be taut.

Chain wear is not always even, so you should repeat

this measurement at different chain positions.

I Chain tension

155 ... 58 mm (2.17 ...

2.28 in)

If the chain tension does not meet the specification:

- Adjust the chain tension. (

p. 127)

Finishing work

- Remove the motorcycle from the lift stand. (

p. 12)

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды