Husqvarna F2303Q0 Скачать руководство пользователя страница 220

Страница: 220 / 322

17 ENGINE

Check needle bearings

for damage and wear.

If there is damage or wear:

Change the needle bearings.

310091-10

Check the pivot points of main shaft

and countershaft

for damage and wear.

If there is damage or wear:

Change the main shaft and/or countershaft.

Check the tooth profiles of main shaft

and countershaft

for damage and wear.

If there is damage or wear:

Change the main shaft and/or countershaft.

Check the pivot points of idler gears

for damage and wear.

If there is damage or wear:

Change the gear wheel pair.

Check the shift dogs of idler gears

and sliding gears

for damage and wear.

If there is damage or wear:

Change the gear wheel pair.

Check the tooth faces of idler gears

C,,

sliding gears

and fixed gear

for damage and wear.

If there is damage or wear:

Change the gear wheel pair.

Check the tooth profiles of sliding gears

for damage and wear.

If there is damage or wear:

Change the gear wheel pair.

Check sliding gear

for smooth operation in the profile of main shaft

If the sliding gear does not move freely:

Change the sliding gear or the main shaft.

Check shift collar

for damage and wear.

If there is damage or wear:

Change the shift collar.

Check sliding gear

and shift collar

for smooth operation in the profile of countershaft

CD.

218

If the sliding gear or shift collar is stiff:

Change the sliding gear, shift collar, or countershaft.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды