Husqvarna F2303Q0 Скачать руководство пользователя страница 255

Страница: 255 / 322

LUBRICATION SYSTEM 20

Condition

The engine is at operating temperature.
-

Check the engine oil level.

Info

After switching off the engine, wait one minute
before checking the level.

The engine oil level is between the middle of the level
viewer

and the upper edge of the level viewer

C,.

If the engine oil does not reach the middle of level

viewer

Add engine oil. (

IUI

p. 256)

Changing the engine oil and oil filter cleaning the oil screens

Warning

Danger of scalding

Engine and gear oil get very hot when the motorcycle is ridden.

Wear suitable protective clothing and safety gloves.

In the event of scalding, rinse the area affected immediately with lukewarm water.

Note

Environmental hazard

Hazardous substances cause environmental damage.

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

Check the O-rings for damage.

Replace damaged O-rings.
Drain the engine oil while the engine is at operating temperature.

Preparatory work

Park the motorcycle on a level surface.

Main work

Place an appropriate container under the engine.
Remove oil drain plug

with the magnet and seal ring.

253

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды