Husqvarna F2303Q0 Скачать руководство пользователя страница 200

Страница: 200 / 322

17 ENGINE

17.4.14 Checking crankshaft run-out at bearing pin

- Position the crankshaft on a roller block.

- Turn the crankshaft slowly.

Check the crankshaft run-out on both bearing pins.

Crankshaft - run-out on

bearing pin

� 0.03 mm (� 0.0012 in)

If the crankshaft run-out at the bearing pin is larger than

the specification:

17.4.15 Measuring the crankshaft end play

- Align the crankshaft.

- Insert the crankshaft into the right section of the engine case.

198

•

Info

Do not forget the dowels.

- Mount the left section of the engine case.

- Mount and tighten the screws.

Guideline

Screw, engine case

110 Nm (7.4 lbf ft)

- Mount the dial gauge support on the engine case and mea

sure and note down the crankshaft axial play.
Guideline

Crankshaft - axial play

0.50 ... 0.60 mm (0.0197 ...

0.0236 in)

If the measured value does not meet specifications:

- Remove the crankshaft.

- Remove the crankshaft bearing inner race. (

p. 195)

- Calculate the thickness of the compensating disks.

- Add or remove compensating disks equally on both

sides.

Info

If the axial play is too small, remove compen

sating disks.

If the axial play is too large, add compensating

disks.

- Install the crankshaft bearing inner race. (

p. 195)

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды