Husqvarna F2303Q0 Скачать руководство пользователя страница 130

Страница: 130 / 322

14 WHEELS

400227-01

�-----

2 3

16 17 18

400987-10

128

Main work

Shift the transmission to neutral position.

Check the chain, rear sprocket and engine sprocket for wear.

If the chain, rear sprocket or engine sprocket is worn:

Change the drivetrain kit.(� p. 131)

Info

The engine sprocket, rear sprocket and chain
should always be replaced together.

Pull on the top section of the chain with the specified

weight

Guideline

Weight, chain wear mea
surement

10 ... 15 kg (22 ... 33 lb.)

Measure distance G) of 18 chain rollers in the lower chain

section.

Info

Chain wear is not always even, so you should repeat
this measurement at different chain positions.

Maximum distance G)

from 18 chain rollers at the
longest chain section

272 mm (10. 71 in)

If distance G) is greater than the specified measurement:

Change the drivetrain kit.(� p. 131)

Info

When a new chain is mounted, the rear
sprocket and engine sprocket should also be
changed.

New chains wear out faster on an old, worn

rear sprocket or engine sprocket.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды