Husqvarna F2303Q0 Скачать руководство пользователя страница 20

Страница: 20 / 322

6 FORK, TRIPLE CLAMP

6.8

Removing the fork legs

Warning

Danger of accidents

Oil or grease on the brake

discs reduces the braking effect.

- Always keep the brake discs free of oil and

grease.

- Clean the brake discs with brake cleaner when

necessary.

- Clean and oil the dust boots and inner fork tubes of both fork

legs.
I Universal oil spray (

p. 293)

- Press the dust boots back into their installation position.

- Remove excess oil.

Finishing work

- Install the fork protector. (

!al

p. 20)

- Remove the motorcycle from the lift stand. (

p. 12)

Preparatory work

- Raise the motorcycle with a lift stand. (

p. 12)

- Remove the front wheel. (

p. 120)

Main work

- Remove screws

and take off the clamp.

- Allow the brake caliper and brake line to hang loosely to the

side.

- Loosen screws

Remove the left fork leg.

- Loosen screws fi). Remove the right fork leg.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды