Husqvarna F2303Q0 Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 322

background image

WIRING HARNESS, BATTERY 15

Charging the 12 V batte�

Warning

Risk of injury

12 V batteries contain harmful substances.

-

Keep 12 V batteries out of the reach of children.

-

Keep sparks and open flames away from 12 V batteries.

-

Only charge 12 V batteries in well-ventilated rooms.

-

Maintain a minimum clearance from inflammable materials when charging 12 V batteries.
Minimum clearance

1 m (3 ft)

-

Do not charge deeply discharged 12 V batteries if the charge is already below the minimum voltage.
Minimum voltage before the start of the charge

9 V

-

Dispose of 12 V batteries with less than the minimum voltage correctly.

Note

Environmental hazard

12 V batteries contain environmentally hazardous materials.

-

Do not dispose of 12 V batteries as household waste.

-

Dispose of 12 V batteries at a collection point for used batteries.

Note

Environmental hazard

Hazardous substances cause environmental damage.

-

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

Even when there is no load on the 12 V battery, it discharges steadily.

The charging level and the method of charging are very important for the service life of the 12 V battery.

Rapid recharging with a high charging current shortens the service life of the battery.
If the charging current, charging voltage, and charging time are exceeded, the 12 V battery will be

destroyed.

If the 12 V battery is depleted from starting the vehicle repeatedly, the battery must be charged immedi

ately.

If the 12 V battery is left in a discharged state for an extended period, it will become deeply discharged

and suffer a loss of capacity, destroying the battery.

The 12 V battery is maintenance-free.

311910-10

Preparatory work

-

Press and hold the kill switch e>q while the engine is idling until

the engine stops.

-

Remove the air filter box cover. (

0

p. 96)

-

Remove the seat. (

0

p. 1 00)

-

Disconnect the negative cable of the 12 V battery. (

8

p. 136)

Main work

-

Connect the battery charger to the 12 V battery. Adjust the
battery charger.

EU battery charger

XCharge-professional

(00029095050)

(

ra!l

p. 294)

Alternative 1

US battery charger

XCharge-professional

(00029095051) (

ra!l

p. 295)

139

«
...
139
140
141
142
143
...
»

Содержание F2303Q0



































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для F2303Q0

Бренд: Sachs Bikes Страницы: 83

Бренд: Yamaha Страницы: 96

Бренд: Honda Страницы: 100

RACE 13100CP520

Бренд: Yoshimura Страницы: 7

Бренд: Dakota Digital Страницы: 7

Бренд: METRAKIT Страницы: 53

Fastrax 50144-00

Бренд: Dowco Страницы: 3

Бренд: Baja motorsports Страницы: 20

Бренд: Yoshimura Страницы: 7

Бренд: Suzuki Страницы: 440

SBL.04.650.10000/B

Бренд: SW-Motech Страницы: 2

KTM 1190 LED Light Bar

Бренд: CYCLOPS Страницы: 4

Бренд: GAS GAS Страницы: 26

Бренд: Arai Helmet Страницы: 12

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды