Husqvarna F2303Q0 Скачать руководство пользователя страница 222

Страница: 222 / 322

17 ENGINE

17.4.45 Assembling the countershaft

Info

Use new lock rings with every repair.

Preparatory work

Lubricate all parts carefully before assembling.

Check the transmission. (

p. 217)

Main work

310090-10

Secure the countershaft in the bench vise with the toothed end facing downward.

Guideline

Use soft jaws.

Mount needle bearing

and second-gear idler gear

onto the countershaft with the protruding collar

facing downward.

Mount stop disk

and lock ring

C,.

Mount second/fourth-gear shift collar

with the shift groove facing up.

Mount lock ring (3 and stop disk @.

Mount needle bearing

and the fourth-gear idler gear

with the collar facing up.

Mount needle bearing 4D) and the third-gear idler gear

with the collar facing down.

Mount stop disk

and lock ring 41).

Mount the fifth-gear sliding gear

with the shift groove facing down and stop disk G).

Mount needle bearing Gs), first-gear idler gear

with the recess facing downward, and stop disk

Gs).

Finally, check all the gear wheels for smooth operation.

220

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды