Husqvarna F2303Q0 Скачать руководство пользователя страница 96

Страница: 96 / 322

10 EXHAUST SYSTEM

10.4

Chan

Warning

Main work

- Detach spring

I Spring hook (5030501700004) (

ll!:!l

p. 307)

- Remove screws

with the washers and take off the main

silencer.

Main work

- Mount main silencer. Mount screws

with the washers, but

do not tighten yet.
Attach spring

I Spring hook (5030501700004) (

p. 307)

- Tighten screws

with the washers.

Guideline

Remaining screws,

chassis

Finishing work

- Install the right side cover. (

p. 100)

of the main silencer

10 Nm (7.4 lbf ft)

Danger of burns

The exhaust system gets very hot when the vehicle is driven.

- Allow the exhaust system to cool down before performing any work on the vehicle.

•

Info

Over time, the fibers of the glass fiber yarn escape and the damper "burns" out.

Not only is the noise level higher, the performance characteristic changes.

Preparatory work

- Remove the right side cover. (

ll!:!l

p. 100)

- Remove the main silencer. (

ll!:!l

p. 93)

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды