Husqvarna F2303Q0 Скачать руководство пользователя страница 221

Страница: 221 / 322

- Check stop disks @ for damage and wear.

If there is damage or wear:

- Change the stop disks.

- Use new lock rings

in every repair.

- Check distance sleeve� for damage and wear.

If there is damage or wear:

- Change the distance sleeves.

17.4.44 Assembling the main shaft

Info

Use new lock rings with every repair.

Preparatory work

- Lubricate all parts carefully before assembling.

- Check the transmission. (

p. 217)

Main work

- Secure the main shaft in the vise with the gear teeth facing downward.

Guideline

I Use soft jaws.

310084-10

- Mount needle bearing

and mount fifth-gear idler gear

with the shift dogs facing up.

- Mount stop disk

and lock ring

C,.

- Mount third/fourth-gear sliding gear

with the small gear wheel facing downward.

- Mount distance sleeve (D.

- Mount lock ring@.

- Mount second-gear fixed gear

with the collar facing downward and mount stop disk

@).

- Finally, check all the gear wheels for smooth operation.

ENGINE 17

219

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды