Husqvarna F2303Q0 Скачать руководство пользователя страница 192

Страница: 192 / 322

17 ENGINE

17.4.2

190

401797-01

Guideline

Oil nozzle, pis

ton cooling

2 Nm (1.5 lbf ft)

Loctite

243

™

Blow compressed air through all oil channels and check that

they are clear.

Finishing work

Install the oil pressure control valve. (

p. 192)

...

Working on the left section of the engine case

310057-10

Remove all remaining dowels.
Remove screw

Remove oil spray tube

Remove screws (D.
Remove the bearing retainers.
Remove shaft seal ring

of the countershaft and shaft seal

ring

of the shift shaft.

Remove any remnants of sealing compound and clean the

engine case section thoroughly.

- Warm the engine case section in an oven.

Guideline

1150 °C (302 °F)

Knock the engine case section against a level wooden board.

This will cause the bearings to drop out of the bearing seats.

Info

Any bearings that remain in the engine case section

must be removed using a suitable tool.

Remove washer (D.

- Warm the engine case section again.

Guideline

1150 °C (302 °F)

Position washer (D.
Insert the new cold bearings in the bearing seats of the

heated section of the engine case; if necessary, use a

suitable press drift to push them all the way in and make

them flush.

Содержание F2303Q0



































































































































































































































































































































Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды

Husqvarna F2303Q0, Руководство по ремонту

Результаты поиска

Содержание F2303Q0

Отзывы:

Похожие инструкции для F2303Q0

Бренды по названию

Популярные бренды